 |
Product #3 Injection Resin 3.5:1-
a
proprietary low viscosity, high modulus, quick strength, epoxy-based
binder
developed for structurally rebonding cracks, delaminations and hollow
planes
in Portland cement concrete. Can also be used in certain types of wood
injection. This Product is a special order product requiring a
minimum quantity. Check with Epoxy.com Technical support for the current
minimum order.
If you are looking for a 2:1 mix ration please see Epoxy.com
Product #300-306 |
|
|
Product # 415 Elastomeric Membrane now called
Product #452 Polyurethane Membrane Standard
Non-Stocking Made to
Order / Minimum Quantity Required 45 gallons.
For smaller quantities use Product #459. |
|
|
Product #416
Polyurethane Coating a moisture-cured, liquid applied,
polyurethane, based on Aliphatic Isocyanides in combination with
additives and pigments to produce a wear resistant, protective and
decorative floor coating, for interior and exterior applications. It is
primarily used as the protective topcoat of the
450 and
450X2 deck coating systems, but when used with the proper primer,
can be used as a stand alone coating.
Non-Stocking Made to
Order / Minimum Quantity Required 35 gallons .
For smaller quantities use
Product #402 |
|
|
Product #417
Elastomeric Waterproofing A black, liquid applied
single-component moisture-cured polyurethane coating, designed to form a
seamless, flexible rubber membrane impervious to moisture. CompositioA
black, liquid applied single-component moisture-cured polyurethane
coating, designed to form a seamless, flexible rubber membrane
impervious to moisture. Composition: Polyurethane elastomer. A
two-component system is available, which does not depend on atmosphere
moisture to cure. Type I: For horizontal surfaces. Type II: For vertical
surfaces. USES: allows expansion and contraction over a broad
temperature range and maintains waterproofing properties under
continuous exposure to water. Type II has a thixotropic consistency and
may be used on vertical as well as horizontal surfaces. 417 remains
flexible from -75°F to +175°F (-59°C to 79°C). Use as a waterproof
membrane is intended for use wherever overflow water must be contained
.
Non-Stocking Made to
Order / Minimum Quantity Required 75 gallons. For
smaller quantities use
Product # 449. |
|
|
Product #418 Elastomeric Membrane,
a black, self-leveling, liquid applied, two-component polyurethane
system, designed to form a tough rubber membrane impervious to moisture.
Type I: For horizontal surfaces Type II: For vertical surfaces.
Composition: Polyurethane elastomer. A two-component system, which does
not depend on atmosphere moisture to cure. Basic Uses: Once cured, #418
allows expansion and contraction over a broad temperature range and
maintains flexibility and waterproofing properties under continuous
exposure to water above or below grade. PRODUCT #418 has a thixotropic
consistency and may be used on vertical as well as horizontal surfaces.
PRODUCT #418 remains flexible from -75° to 175°F.
Non-Stocking Made to
Order / Minimum Quantity Required 70 gallons
For smaller quantities use
Product # 449. |
|
|
Product #419 Waterproofing
Membrane Black Waterproofing Industrial Strength is
a black, liquid applied, two-component, high solids, chemical cured,
polyurethane coating designed to form a tough rubber membrane impervious
to moisture. Composition: Polyurethane elastomer. A two-component system
which does not depend on atmospheric moisture to cure. Basic Uses: Once
cured, #419 allows expansion and contraction over a broad temperature
range and maintains flexibility and waterproofing properties under
continuous exposure to water above or below grade. It has a thixotropic
consistency and may be used on vertical as well as horizontal surfaces.
The #419 waterproof membrane is intended for use on steel, wood,
concrete, asphalt, tanks, ponds, roofs, foundations, etc.
Non-Stocking Made to
Order / Minimum Quantity Required 60 gallons smaller quantities use
Product # 449. |
|
|
System #430 Elastomeric Multi-Colored
Decking System is a l iquid-applied, single-component,
moisture-cured, polyurethane deck covering system. For waterproofing
patios, sundecks, stairways, balconies, etc. Product #430
can be used on all decks where a skid-resistant, long-lasting,
wear-resistant, water-proof surface is required. It may be used on new
decks as well as on old concrete decks which are damaged, or cracked.
The system is suitable for exterior as well as interior applications in
all kinds of climates. The coating retains its elastomeric properties in
below freezing weather as well as in very hot climates.
Non-Stocking Made to
Order / Minimum Quantity Required approximately 900 SF |
|
|
EpoxySystems’ PRODUCT #431
is a two component, flame retardant foam especially manufactured to
provide a rigid foam with physical properties similar to that of timber
or cement grouts, at a convenient one to one ratio, A to B, light black
in color.
Product #431 will bond to wet, moist or dry surfaces, even to
Plexiglas, with no shrinkage and ample pot life after mixing A & B
components.
Non-Stocking Made to
Order / Minimum Quantity Required approximately 50 gallons |
|
|
#450 Elastomeric
Flooring system provides a waterproof, elastomeric,
traffic bearing deck coating. It is a monolithic system that
incorporates excellent adhesion, flexibility, impact, abrasion
resistance, and chemical resistance. Petroleum products or cooling tower
water spillage have little or no effect on the coating. Physical
stresses imposed by vibration of equipment will not cause delamination
or rupture of the coating. The elastic properties of all system
components enable the complete system to give and work with all but the
most unusual movement of the floor or deck.
Non-Stocking Made to
Order / Minimum Quantity Required approximately 1000 SF |
|
|
System
#450 Mechanical Room Flooring System -
Liquid-applied, single-component, moisture-cured, polyurethane deck
covering system. 450MR system provides a waterproof, elastomeric,
traffic bearing deck coating. It is a monolithic system that
incorporates excellent adhesion, flexibility, impact, abrasion
resistance, and chemical resistance. Physical stresses imposed by
vibration of equipment will not cause delamination or rupture of the
coating. The elastic properties of all system components enable the
complete system to give and work with all but the most unusual movement
of the floor or deck.
Non-Stocking Made to
Order / Minimum Quantity Required approximately 1000 SF |
|
|
System
#450X2 Urethane Decking System double strength is an
elastomeric coating system for walking decks, balconies, patios, etc.,
where an absolutely waterproof coating is crucial, such as above living
quarters and any other occupied areas
Non-Stocking Made to
Order / Minimum Quantity Required approximately 1000 SF or use
Epoxy.com System #485. |
|
|
System #450HT- High Tensile
Strength version of the 450 system for extra heavy duty applications,
like vehicular traffic. Epoxy.com Product #450HT is a liquid-applied,
single component, moisture-cured, seamless, slip resistant,
polyurethane, waterproof deck coating.
Non-Stocking Made to
Order / Minimum Quantity Required approximately 1000 SF |
|
|
Product #451
Aromatic Polyurethane Coating -
is an aromatic, liquid applied, single-component, moisture cured
polyurethane floor coating for use in indoor applications such as
industrial plants, mechanical rooms, and locations where surfaces must
withstand pedestrian traffic
Non-Stocking Made to
Order / Minimum Quantity Required 40 gallons Use
Product # for smaller quantities use Epoxy.com
Product #402. |
|
|
Product #452
Polyurethane Membrane Standard is a liquid applied,
single component, moisture-cured polyurethane. It is the major component
of all EPOXYSYSTEMS’ PRODUCT #450 deck coating systems.
Non-Stocking Made to
Order / Minimum Quantity Required 45 gallons.
For smaller quantities use Product #459 |
|
|
Product #453 Elastomeric Mortar-
is a sloping system using an elastomeric binder adhesive mixed with
aggregate for sloping decks, based on polyurethane elastomers.
Non-Stocking Made to
Order / Minimum Quantity Required 40 gallons. |
|
|
Product
#454 LVOC Polyurethane Membraneis
a liquid-applied, single component, aromatic, moisture-cured
polyurethane which will not blister or gas. It may be substituted for
our Epoxy.com Product #452.The
Epoxy.com 454 LVOC Non-gassing Low VOC waterproofing membrane
used with the all Epoxy.com 430 and 450 Series systems.
Epoxy.com 454 LVOC Non-gassing may be used to fill minor
cracks in concrete, except for expansion joints where Epoxy.com
Product #910 is recommended.
Non-Stocking Made to
Order / Minimum Quantity Required 45 gallons or
use Product #459 |
|
|
Product #458
2Component Urethane Coating is a liquid-applied,
two-component, catalytic cured polyurethane floor and wall coating for
use in air fields, industrial plants, stores, and other locations where
surfaces must withstand heavy use of foot traffic. It provides a durable
finish that protects floors against occasional chemical spillage, dirt,
grease and oil. It gives industrial floors a well maintained look while
retaining a glossy appearance. Dusting of concrete floors is eliminated
when the surface is sealed with PRODUCT #458 and, as dirt and oils are
prevented from penetrating the concrete, detergent and water easily
clean the floor. PRODUCT #458 in pigmented form may be used on floors
to hide an unsightly appearance of the substrate or to provide a
reflective, bright appearance that will lighten up a warehouse,
highlighting work areas and traffic lanes.
Non-Stocking Made to
Order / Minimum Quantity Required 45 gallons. or
use
Product #402 |
|
|
Product #460 Polyurethane Membrane and
Coatingi s a two component, aliphatic, 100% solids, Zero
VOC, elastomeric, traffic coating system for walking deck surfaces.
Concrete or Plywood substrates. For waterproofing walking decks,
balconies plazas, parking decks, mechanical room floors, etc. Designed
for pedestrian and vehicular traffic..
Non-Stocking Made to
Order / Minimum Quantity Required 60 gallons. |
|
|
Product #824 Concrete Stain
and Coating
is a one component, water-repellant concrete stain. EPOXYSYSTEMS’
PRODUCT
#824 penetrates existing concrete and imparts color and uniformity the
surface
without affecting the natural texture. Standard colors are white and
gray
many other colors of concrete are available. - Special Order
Product.
Can be used only on certain projects. Minimum quantities apply. Contact
Epoxy.com Tech Support for
details. |
|
|
Product
#826 Floor Curing Agent - Minimum purchase of 20 each 55
gallon drums
required. |
|
|
Product #888 Epoxy Primer is a two-component, epoxy resin
based concrete, metal, and wood primer for use with a wide variety of
EpoxySystems’ Elastomeric systems. The primer may also be used with
other polyurethane and epoxy systems, including joint sealants. Non-Stocking
Made to Order / Must be ordered with a system of $2,500 or more.
or use
Product #899 Primer. |
|
|
Product
#889
is a one component, moisture cured primer for concrete and
wood surfaces. Used to promote adhesion on deck coating systems and
joint sealants to concrete and wood.Non-Stocking
Made to Order / Must be order with a decking system of $2,500 or more.
or use
Product #899 Primer. |
|
|
Product #893 Water
Based Epoxy Primer for Multi-Use System
is a fast drying, two-component waterbased epoxy primer for use with our
polyurethane based deck coating systems and joint sealants. The product
has low odor and is non flammable. Non-Stocking
Made to Order / Must be order with a decking system of $2,500 or more.
or use
Product #899 Primer. |
|
|
Product #904 Color Pack for
Product #916
Polymeric Joint Sealant
Non-Stocking Made to Order / Must be order with 30 units or more of
Product #916. |
|
|
Product #905 Polysulfide Caulk
- Superseded by Product #900 (Gun
Grade) or Product #901 (Pourable) which is available in quantities
as small as 1.5 gallons. Contact
EpoxySystems' Tech Support for details.
|
|
|
Product
#910 Polyurethane Caulk - Single Component is a
one-part, moisture-cured, self-leveling or gun-grade non-staining,
polyurethane sealant which cures at ambient temperature to a firm,
flexible tear-resistant rubber. It is highly resilient and has excellent
recovery characteristics after extended periods of compression or
elongation.
Non-Stocking Made to Order / Must be order in quantities of 325 each
10.5 oz tubes or more, 200 each 20oz tubes or 125 each 30 oz tubes.
or use
Product #900 (Gun Grade) or Product #901 (Pourable)
. |
|
|
Product
#913
a two-part, self leveling or
gun-grade, polysulfide sealant , which effectively seals
joints that are subject to structural or thermal movement, as well as
non-moving joints, against infiltration of water and dirt. Non-Stocking
Made to Order / Must be order in quantities of 18 units or more.
or use
Product #900 (Gun Grade) or Product #901 (Pourable)
. |
|
|
Product #914 a two-part Polyurethane
Sealant
is a Two-component, cold applied, polyurethane based joint sealant,
modified with bitumen. For sealing joints in airfield runways, parking
aprons and other areas where joints may be subjected to fuel spillage.
Non-Stocking Made to Order / Must be order in quantities of 36 units or
more. or use
Product #900 (Gun Grade) or Product #901 (Pourable)
. |
|
|
Product #916 a two-component, low
modulus, polyurea based joint sealant designed to tolerate
significant joint movement, up to + 25%. Provides a flexible, durable,
weather-tight seal for all types of building joints, such as expansion
joints in masonry and metal curtain walls, perimeter joints of sashes,
panels and doors, water reservoirs, etc.
Non-Stocking Made to Order / Must be order in quantities of 30 units or
more. or use
Product #900 (Gun Grade) or Product #901 (Pourable)
. |
|
|
Product #917 Jet Fuel
Resistant Polysulfide based , coaltar modified joint sealant.
Basic Uses: For sealing joints on airfield runways, parking aprons and
other areas where joints may be subject to fuel spillage and jet blast.
Non-Stocking Made to Order / Must be order in quantities of 21 units or
more. or use
Product #900 (Gun Grade) or Product #901 (Pourable)
. |
|
|
930 Polyurea Rapid Curing
Joint Sealant Non-Stocking
Made to Order / Must be order in quantities of 70 units or more. |
|
|
Product #4240 is a rigid two
component
closed cell foam impervious to water and moisture. Product
#4240
can be used where foam is needed to fill voids in concrete and timber
materials.
PRODUCT #4240 contains flame retardant and is considered Class B
non-burning
Foam when tested in accordance to ASTM E-84. This is a special
made to order product Requiring a minimum quantity. Check with
Epoxy.com Technical Support Department for the current minimum order. |
Proper mixing and installation is critical to the optimal success of all
product. See Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you have.