|
|
|
Epoxy.com Product #460 Two Component Aliphatic, 100% Solids VIRTUALLY NO ODOR, ZERO VOC, PEDESTRIAN DECK COATING This Material requires a minimum product purchase. Please see our Products That Require a Minimum Order Page, or contact Epoxy.com for more information.
EPOXYSYSTEMS’ PRODUCT #460 is a two component, aliphatic, 100% solids, Zero VOC, elastomeric, traffic coating system for walking deck surfaces. Concrete or Plywood substrates. PRODUCT DESCRIPTION Composition: Liquid applied, two-component, flexible, low odor, polyurea deck coating. Basic Uses: For waterproofing walking decks, balconies plazas, parking decks, mechanical room floors, etc. Designed for pedestrian and vehicular traffic. Limitations: All surfaces must be completely free of foreign matter and primed with EpoxySystems’ Product #893 (Zero VOC), where necessary. EPOXYSYSTEMS’ PRODUCT #460 has a relatively short work life, so once it is mixed, the coating must be poured onto surface and applied immediately. Colors: Concrete Grey and Tan. Custom matched colors are available with minimum required quantities.
Sizes: Available in 1.5 gallon kits, 4.5 gallon kits. WARNINGS AND HAZARDS Before using the products, always refer to MSDS for important warnings and safety information. Use only in areas with adequate ventilation. Avoid breathing vapors. Keep away from heat and flame. Avoid contact with eyes and skin. In the event of skin contact, remove immediately and wash with warm, soapy water. Wear suitable eye protection. Always wash hands before eating. TECHNICAL DATA
INSTALLATION Surface Preparation: All surfaces which are to receive EPOXYSYSTEMS’ PRODUCT #460 shall be free of contamination such as water, curing compounds, hardeners, bond breakers, paint, etc. A light broom finish is recommended for concrete surfaces.It is desirable to water-cure concrete in lieu of curing compounds. Contaminants should be removed by sandblasting or bead-blasting. Except for non-moving shrinkage cracks, all other cracks must be sealed with EPOXYSYSTEMS’ PRODUCT #460 and taped with 4" Tietex. All surfaces, where necessary, must be primed with EpoxySystems' Product #893 Water Based Epoxy PRIMER (Zero VOC) prior to application of the coating system at a rate of 200-250 square feet per gallon.
Application: Lightly stir the A-Component (pigmented side) for 2-3 minutes using a jiffy mixing blade to evenly distribute the pigments that may have settled to the bottom of the container. Then pour "B" Component (clear side) into the "A" Component. Scrape the container to drain all the "B" Component into the "A" Component. Mix thoroughly using a jiffy mixing blade attached to a low speed drill to a uniform color without any streaks. Mix for 2-3 minutes. Once mixed, immediately pour EPOXYSYSTEMS’ PRODUCT #460 onto the surface of the substrate. Use squeegee to evenly apply the material, then back roll using a roller to break air bubbles. Note: Higher temperatures will reduce the work life. EPOXYSYSTEMS’ PRODUCT #460 shall be applied to the primed concrete at a rate of 80 square feet per gallon. Following a 24 hour cure time of the EPOXYSYSTEMS’ PRODUCT #460, apply the EPOXYSYSTEMS’ PRODUCT #460 at the rate of 80 square feet per gallon. While coating is in a fluid condition, broadcast desired aggregate at the rate of 10-15 pounds per 100 square feet and backroll to ensure even distribution of the grit. Allow a minimum of 72 hours cure time before allowing any heavy traffic on the finished system. PRODUCT WARRANTY Satisfactory results depend not only upon quality products but also upon
factors beyond our control; methods of application and site conditions are
examples of such factors and can affect product performance. This warranty
consequently extends only to products installed in strict accordance with the
manufacturer’s specifications. It is the user’s responsibility to satisfy
himself, by his own information and tests, of the suitability of the product for
his own intended use; user assumes all risk and liability resulting from his use
of the product. The substrate to which the product is applied must be sound
structurally and otherwise. Structural or substrate failures or imperfections
resulting in damage to or failure of the product are not covered by this
warranty. Since the use of the product is beyond the control of the
manufacturer, the manufacturer assumes no liability for misapplication and
misuse of the product. This warranty does not cover consequential damages, nor
does it cover the labor attendant to replacing product in the event of a product
failure. The warranty only extends to replacement of the product itself. If this product is proven to be defective in manufacture will be replaced at no charge. Since the use of these products is beyond our control we cannot accept damage in excess of the purchase price of these products.
MAINTENANCE Since, as with all deck coatings, the topcoat is subject to staining by such foreign matter as nitrates, fertilizers, hard water, and other substances, it must be maintained. Please refer to the Maintenance Manual for proper maintenance procedures. The manufacturer is not liable for staining caused by hard water deposits, nitrates, fertilizers and other foreign matter. If EPOXYSYSTEMS’ PRODUCT #460 is damaged, it can be repaired by cleaning the surface with M.E.K. and recoating it with the EPOXYSYSTEMS’ PRODUCT #460 system.
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
