Epoxy.com
Product #600
Flexibilized Novolac Epoxy Coating
DESCRIPTION:
Epoxy.com PRODUCT #600 Flexibilized Novolac Epoxy Coating is a
two-component, 100% solids epoxy coating based on multi-functional high
performance flexibilized resin. Epoxy.com PRODUCT #600 Flexibilized Novolac
Epoxy Coating provides corrosion resistant protection to steel, other metals and
concrete. Epoxy.com PRODUCT #600 Flexibilize Novolac Epoxy Coating has excellent
resistance to chemicals up to 300°F. Epoxy.com PRODUCT #600 Flexibilized Novolac
Epoxy Coating is resistant to continuous immersion in water up to 212°F .
Epoxy.com PRODUCT #600 Flexibilized Novolac Epoxy Coating is formulated in a
convenient 1 to 1 ratio, by volume mix ratio and has a long pot life to simplify
application. Epoxy.com PRODUCT #600 Flexibilized Novolac Epoxy Coating is more
effective in applications which entail force curing.
ADVANTAGES:
- Excellent corrosion barrier properties.
- Excellent chemical resistance.
- Excellent adhesion to most metals.
- It protects concrete, steel, or wood from salts, acids, and alkalies
WHERE TO USE
For Chemical Protection Of:
- Steel Tanks
- Piping
- Heat Exchangers
- Condenser Boxes
- Hot Water Tanks
- Manholes
SURFACE PREPARATION:
Steel Surfaces:
Steel surfaces should be abrasive
blasted to a commercial gray metal finish as specified by the Steel
Structures Painting Council. For immersion service, blast to near
white blast - SSPC SP-10.
Concrete Surfaces
Contamination and
other foreign materials must be mechanically removed to ensure a
satisfactory bond. All dust and debris must be thoroughly removed.
For more information on surface preparation see
Epoxy.com Surface Preparation Guide.
MIXING
Stir Components "A" & "B" thoroughly before mixing. Combine one part
by volume of "A" with one part by volume of "B" (mixing ratio 1:1). Mix
for not less than three minutes using a slow speed drill (300 to 600
rpm) and Epoxy.com Mixing Paddle. Scrape side and bottom to ensure
thorough mixing. Avoid entrapping air. Apply immediately after mixing.
APPLICATION
Epoxy.com Product 3600 Flexibilized Novolac Epoxy Coating may be
applied by brush, roller, or spray. All spray equipment must employ
traps to prevent water and oil from contaminating coating. Thinning may
be required for spraying. Heating may be required for spraying. Heating
will shorten pot life to 20 minutes at 100°F. Apply immediately after
mixing. Apply 10 mils wet film thickness. Apply topcoat after primer is
tack free between 4 and 24 hours.If heated, the tack free time will be
reduced. Epoxy.com Fiber Reinforcement is recommend for tank relining.
Apply the first coat of Epoxy.com Product #600 Flexibilize Novolac epoxy
Coating then place reinforcement. Work reinforcement into coating.
Second coat of Epoxy.com Product #600 is applied after about 3 hours. Be
sure to apply second coat within 24 hours of first coat.
COVERAGE
100-200 square feet per gallon (per coat), dependent upon surface
texture and desired thickness. When applying Fiber Reinforcement the
coverage will be less.
PACKAGING
Epoxy.com Product #600 Flexibilized Novolac Coating is packaged in 2
gallon and 10 gallon units.
CAUTION:
WARNING! A Component contains epoxy resin. B
Component contains alkaline amines; strong sensitizer. May cause skin
sensitization or other allergic responses. Use with good ventilation,
particularly if material is heated or sprayed. Prevent all contact with
eyes or skin. Wear protective clothing, goggles, gloves, and/or barrier
creams. Keep container closed when not in use. Wash thoroughly after
handling.
PHYSICAL PROPERTIES
TYPICAL PROPERTIES PRODUCT #600
| Pot Life @ 70-75° F |
|
45-60 min. Pot life after mixing is approximate |
| Working Time |
Application Time @ 70-75° F |
35 min. |
| Cure Time @ 70-75° F |
|
Foot Traffic Overnight/16 hrs.
Light Vehicular Traffic 1-2 days |
| Service |
|
3-7 days |
| Mix Ratio (by volume) |
Part A: Part B |
1:1 |
| Primer (concrete) |
|
Self-Priming |
| Hardness, Shore D |
ASTM D 2240 |
65-80 |
| Tensile Strength, psi |
ASTM D 638 7 days cure @ 70-75° F |
4,000 + |
| Elongation % @ Break |
ASTM D 638 7 days cure @ 70-75° F |
5-10 |
| Compressive Strength, psi |
ASTM D 575 |
10,000+ |
| Impact Strength, in.-lbs. |
ASTM D 4226 Falling Ball Method |
10+ |
| Low Temperature Flexibility |
ASTM D 3111,
360° Bend 1/4" Mandrel @ -15° F
10 mil
thickness |
Passed |
|
|
Proper mixing and installation is critical to the optimal success
of all product. See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
350 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers. |
Copyright © 1994-2013 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Home]
[Catalog of Products]
[Where to Start]
[[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive Flooring]
[Applications]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Industrial Floors]
[Injection]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Novolac Epoxy]
[Polymer Systems]
[Primers Sealers]
[Misc.]
[Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]
6475684
|