[Epoxy Home] [Catalog of Products] [Where to Start] [Guide Specs] [Epoxy Installation Guides] [Blog Posts] [Epoxy Bonding Systems] [Chip Floors] [Chemical Resistant Epoxy] [Seamless Coatings] [Conductive Epoxy Flooring] [Crack Injection of Concrete & Wood] [Applications] [Elastomeric Polyurethane Systems]  [Seamless Garage Flooring Resins] [High Temperature Epoxy Resins] [Seamless Industrial Floors] [Joint Systems & Sealants] [Methyl Methacrylate MMA ] [Novolac Epoxy Resins] [Epoxy Mortars & Grouts] [Epoxy Novolac] [Primers Sealers] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Epoxy Installation Tips] [Who We Are]  [Epoxy Tech Data Sheets in Acrobat] [Product MSDS Sheets] [Online Order Authorization Form][Contact UsPhone 352.489.1666

  Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980Contact Us  

Epoxy.com Product #210

100% Solids Coal Tar Epoxy Coating.

Solvent Free - Zero (0) VOC Makes it Excellent for Use In Poorly Ventilated Areas


Epoxy.com Product #210 Coal Tar Epoxy Coating is a two component, 100% solids coating, especially formulated for high build applications. Epoxy.com Product #210 Coal Tar Epoxy Coating produces a tough, flexible, chemical and impact resistant film. Epoxy.com Product #210 Coal Tar Epoxy Coating is formulated to be easily spray applied, as thick as 40 mils in one coat. Epoxy.com Product #210 Coal Tar Epoxy Coating provides excellent resistance to aggressive water, acids, and caustics.


  • Suitable for intermittent exposure to 300°F
  • Excellent chemical resistance
  • Excellent Adhesion
  • Convenient 2A to 3B mix ratio by volume
  • High build to 40 mils per coat
  • 100% solids, 0.0 lbs. VOC
  • Sprayable
  • Tough and flexible
  • Moisture insensitive
  • Low temperature curing


Epoxy.com Product #210 Coal Tar Epoxy Coating meets the performance criteria for the American Water Works Association Specification C-210.

Since the Product #210 Coal Tar Epoxy Coating is 100% solids, it meets the requirements of the U.S. Environmental Protection Agency's V.O.C. Emission.

Color Black
Percentage Solids 100%
Pot Life 1 hour @ 75°F
Cure Times 24 hrs. @ 75°F for light service
Full Cure 7 days*
Adhesion to Steel -ASTM D 1002 1200 psi
Adhesion to Concrete -ASTM C 882 (substrate) Break in Concrete
Tensile Strength -  ASTM D 638 2200 psi
Compressive Strength  -  ASTM C 579 7350 psi
Abrasion Resistance - ASTM D 4060 59.2 mg
Shrinkage ASTM C 883 0%
Pull-Off Test ? ASTM D 4541-85 Cohesion Failure
  *Cure may be accelerated by heat curing @ 140°F for 6-8 hours


All surfaces to receive Epoxy.com Product #210 Coal Tar Epoxy Coating must be clean and structurally sound, free of dirt, grease, oil, paint, etc.

Remove contamination with abrasive blasting, water blasting or wire brush. Make sure all dust is removed after abrasives. Metal should be blasted to SSPC SP-6, 2 to 4 mils profile before coating. Concrete should be blasted or acid etched before coating. Remove all acid with water before coating.


Mix Epoxy.com Product #210 Coal Tar Epoxy Coating at 2A to 3B by volume. Mix well with low speed drill (300 rpm) and Epoxy.com -Mixing Paddle. Stir until uniform, smooth material is seen. Mix minimum of three (3) minutes. Scrape sides and bottom frequently. Avoid entrapping air in mixture. For best results, when spraying, strain material through a 60 mesh screen prior to spraying.


Apply Epoxy.com Product #210 Coal Tar Epoxy Coating by brush or spray. Pot Life  of Epoxy.com Product #210 Coal Tar Epoxy Coatingis 30 minutes @ 100°F. If heated and sprayed, mix only what you can apply within 30 minutes. Spraying this material requires specialized equipment. Both "A" and "B" Components must be heated to 100°F before spraying. A 45:1 airless spray pump with standard airless spray gun through a .031 to .035 reversible tip is needed. Plural component guns may be used with this product. Higher temperatures and larger masses shorten pot life.


5 Gallon Unit = 3 gallons "B" in a 6 gallon pail and 2 gallons "A" in a 2 gallon pail.


80 square feet per gallon @ 20 mils.


Do not use Epoxy.com Product #210 Coal Tar Epoxy Coating below 40°F. Store material under dry conditions. For best results before spraying, rolling, or applying by brush, condition material to 70°F or higher.


"A" Component?WARNING! Contains epoxy resin. May cause skin irritation or allergic response. Avoid contact with skin. Avoid breathing vapor when heated. In case of skin contact, wash thoroughly with soap and water. In case of ingestion, do not induce vomiting.

"B" Component?DANGER! Causes severe burns. Contains alkaline amines. Strong sensitizer. Avoid skin contact. Avoid breathing vapor when heated. Wear protective gloves, goggles and barrier creams. In case of skin contact, wash thoroughly with soap and water. In case of ingestion, induce vomiting. If irritation persists, seek medical attention.


Hit Counter


Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director

 352-533-2167  Technical Support
                         Norm Lambert, President - Technical Support Director 
352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

352-489-1625   Fax line to all Departments

Website:  www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright 1994-2014 (providing online information about the right product for the right job for 20 years) EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  (hereinafter known as "Supplier" warrants its products (when properly stored) for the period of time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylate  and Polyurethanes Six (6) months.  Supplier warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Supplier. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Supplier within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material. No customer, distributor, or representative of Supplier is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Supplier. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Supplier reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.


[Home] [Catalog of Products [MSDS in Acrobat Format]  [Online Ordering Authorization Form] [Add Epoxy.com to Favorites]

Hit Counter