Care and Maintenance of Epoxy.com Epoxy Flooring and Epoxy Coating and Epoxy.com other Reisn Ssytems
Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Care and Maintenance of
Epoxy Flooring Systems and Coatings

Daily Maintenance of Seamless Floorings and Floor Coatings

  • Sweep the floors daily.
  • If abrasive particles  are present they should be removed by mopping with common household detergents and rinsed completely.  Be sure not to use the detergent at a concentration higher than that recommended by the manufacturer of the floor cleaning material.  Be sure to test any cleaner that you haven't used before on a sample of the Seamless Flooring Material or Seamless Floor coating.  You may want to be sure to prepare these samples as you are installing the floor so they will be available to you at a later time.
  • Promptly remove grease, and other contaminants from the surface of the floor.
  • Be sure to rinse off all chemical solutions that may attack the surface.

Weekly Maintenance of Seamless Flooring and Floor Coatings

Smooth Systems

All seamless flooring and floor coatings should be mopped on a regular bases with a neutral soap or detergent, and completely rinsed. Be sure not to use the detergent at a concentration higher than that recommended by the manufacturer of the floor cleaning material. 

Be sure to test any cleaner that you haven't used before on a sample of the Seamless Flooring Material or Seamless Floor coating. 

Mop should be rinsed often. Synthetic mops tend to work better on textured surfaces than cotton mops. The water should be changed frequently as well. Smooth floors are easily cleaned this way. It may be necessary to give extra care to areas that are subject to heavy traffic, hard rubber wheels, and steel wheels that leave marks. In these situations you can use the methods used for textured floors for these more difficult to remove contamination.

Textured Systems

Textured systems may require the use of a stiff bristled brush or floor scrubber to reach to bottom of the anti-skid texture.  Severe problem areas can be treated as follows:

Grease Removal

Grease is typically removed by Tri-sodium phosphate (TSP) or other commonly available biodegradable cleaner. Contact Epoxy.com Technical Support Department with your specific questions.

Removing Dairy Products

Dairy products should be removed immediately as they may cause staining on some types of seamless flooring and seamless floor coating systems.

Tire Marks Removal

Scrub the area(s) with a stiff bristled brush and using the same biodegradable floor cleaner that you are using to mop with.

Stubborn Dirt or Stain Removal

When you are trying to remove stubborn dirt or stains, allow the biodegradable cleaner to set in the area for a little while longer and do the work for you. Then completely rinse to area to remove the cleaner and the dirt.

Chemical Spills

You should always rinse strong chemicals as quickly as possible completely from the surface. Chemicals allowed to dry on the surface typically become more concentrated as they dry.  That may cause the chemical to get concentrated enough to stain or even attack the seamless floor or seamless floor coating.

Waxing and Polishing of Seamless Flooring and Seamless Floor Coatings

Epoxy.com Epoxy and Urethane Seamless Flooring and Seamless Floor Coating Systems are very shinny and so waxing or polishing are not necessary.  If a floor is very old, or has seen extremely high traffic this shine may dull.  If it does then you can wax or polish the floor with standard commercial products that are designed for that purpose.  Better yet, if this happens, you may want to renew or refinish your system - see below.

Renewing and Refinishing Seamless Flooring and Seamless Floor Coating Systems

Epoxy.com Epoxy and Urethane Seamless Flooring and Seamless Floor Coating Systems are designed to withstand heavy traffic and wear.  However, if there is enough traffic and/or abuse to cause the system to loose its shine, or show visible signs of wear, you may wish to restore the floor by "re-glazing" it.  Before re-glazing a flooring system or coating system you need to do the following:

  • Remove all wax, oil, grease and other contaminants from the surface.
  • Lightly sand to break the shine
  • Consult with Epoxy.com Technical Support Department for the proper material to re-glaze you floor.  Be sure to follow all directions for installing the re-glazing material.

 

 Skip Navigation Links

Epoxy.com Home PageExpand Epoxy.com Home Page

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Get important hint, tips, tricks, and product information:  Visit our Blog, and join us on Facebook and Twitter.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2017 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/