Epoxy.com Product #677 Electrostatic Dissipative (ESD) / Conductive Epoxy Coating

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Epoxy.com Product #677

Electro Static Dissipative (ESD) /CONDUCTIVE COATING


DESCRIPTION

Epoxy.com Product #677 is a pigmented, water-based epoxy coating designed to achieve either an electro-static dissipative (ESD) finish or conductive finish by modifying the underlying system components and thickness. Epoxy.com Product #677 has very low odor making it suitable for use in occupied buildings and has high bond strength and adhesion to concrete and other surfaces.

ADVANTAGES

  • Durable, Attractive, Chemical Resistant, Non-Porous, Light Reflective Finish.
  • Low Odor during application and cure.
  • Maintains Electrical Conductivity Performance over the Wear Life of the System
  • Fast Dry and Re-coat Time.
  • Easy Clean-up.
  • Provides an ESD finish in the range of 1,000,000 to 1,000,000,000 ohms resistance when used over a non-conductive primer/basecoat or a conductive finish in the range of 25,000 to 1,000,000 ohms resistance when used over a conductive primer/basecoat.

CONSIDERATIONS

  • Substrate must be above 50�F and relative humidity below 85% for proper curing.
  • Substrate must be free of dirt, waxes, curing agents and other foreign materials.
  • Excessive moisture in the substrate will require a moisture vapor control treatment.

TYPICAL USES

Concrete floors and walls in electronic component assembly areas, data processing, military/aerospace, pharmaceutical plants, hazardous industries (dust or explosion hazards). For use in any areas where the build-up of static electricity is a concern or a spark-proof floor is required.

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared and tested for moisture as outlined in Epoxy.com Surface Preparation Guidelines.

INSTALLATION

Mix Part B of Epoxy.com Product #677 prior to combining. Mix 1 part Part A with 2 parts Part B. Epoxy.com Product #677 at a rate of 200 ft2 per gallon per coat with a short nap roller. Care should be taken to avoid puddles. Two coats are necessary to insure uniform coverage.

Epoxy.com Product #677 Thin-Film ESD Epoxy Coating System � 12-15 Mils
(1,000,000-1,000,000,000 ohms)

MaterialQty./ 1000 SFCoverage
1. Epoxy.com Product #899 Epoxy Primer 4-5 gallons200-250 SF /gallon
2. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons200 SF /gallon
3. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons200 SF /gallon

CLEAN-UP

Clean skin with soap and water. Tools and equipment should be cleaned with warm soapy water, xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.

COMPOSITION

Waterborne Epoxy Resin and Conductive Fillers

COVERAGE

Epoxy.com Product #677, when applied at 200 SF per gallon, yields 5.2 �to 6.0 mils dry film thickness.

TECHNICAL DATA

Viscosity @ 75°F600-1000 CPS
Mixing Ratio1 Part A to 2 Parts B by Volume
Solids Content, by volume50-55%
Volatile Organic Content (VOC)<20 gm/L
Bond Strength to Concrete400-500 psi (100% concretefailure
Weight per Gallon, mixed8.75-9.00 pounds per gallon, mixed

CURE/DRY TIME

Pot Life20-30 min.
Dry to touch6 hours @ 75°F
Recoat8-24 hours @ 75°F
Light Traffic24 hours @ 75°F
�H� Hardness2 days
�5-H� Hardness30 days

AVAILABILITY

Contact Epoxy.com Customer Service Department at 321-206-1833

Maintenance

Remove animal fats, oil, grease or soap film promptly to reduce slipperiness. Epoxy.com Product #677 can be cleaned with neutral soaps and detergents. If long periods of heavy traffic cause wear patterns reapply as need. Anti-skid materials will reduce the effectiveness of the static dissipative properties of this material.  Do not use aggressive anti-skids. It is impossible to get an accurate reading of the conductivity of the floor if anti-skids are used.

Technical Services

Contact Epoxy.com Technical Support with your questions about this product at 352-533-2167. Epoxy.com Technical Support Department can help you with the selection, specification, installation, and maintenance of Epoxy.com products, or visit www.epoxy.com.

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Get important hint, tips, tricks, and product information:  Visit our Blog, and join us on Facebook and Twitter.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2017 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/