DESCRIPTION
Epoxy.com Product #406 is a
two component, chemical resistant, polyurethane coating.
Epoxy.com Product #406
is a low VOC compliant urethane that meets all federal and state environmental air quality
standards. The high gloss finish offers excellent abrasion resistance, chemical and stain resistance,
and superior color retention.Epoxy.com Product #406 can be used equally well on vertical or horizontal
surfaces. It is ideal for concrete floors and walls in warehouses, storage facilities, aircraft hangars,
animal housing, and vehicle maintenance facilities. Available in both clear and pigmented formulations,
Product#406
can be used as a finish coating option for most Epoxy.com Flooring Systems.
ADVANTAGES
-
Excellent Abrasion
Resistance
-
Excellent Chemical &
Stain Resistance
-
Suitable for Both
Exterior & Interior Applications
-
May be Used for Both
Horizontal & Vertical
-
Compliant to Low VOC
Air Regulations
CONSIDERATIONS
- Substrate temperature must be a minimum of 50ºF
- Substrate must be free of dirt, waxes, curing agents, and other foreign materials
- Minimum Application Temperature: 40ºF (contact Epoxy.com for Low Temperature Cure)
- Maximum Application Temperature: 100ºF
COMPOSITION
Two component, catalyzed, chemical resistant polyurethane.
APPLICATION
SURFACE PREPARATION
Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation
Procedures. Work must be performed by trained or experienced contractors or maintenance personnel.
INSTALLATION
Epoxy.com Product #406 is normally applied with a brush, short napped roller, or squeegee and back-rolled
with a short nap roller. Care should be taken to minimize the entrapment of air caused by over-rolling.
Epoxy.com Product #406 can also be applied by airless or conventional spray. May be thinned 9-10% with Ethyl Ethoxy
Propanate (EEP) or Methy Amyl Ketone (MAK).
CLEAN UP
Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.
COVERAGE
Epoxy.com Product #406 Clear will yield approximately 2.9 mils dry film thickness when spread at 300
ft2 per gallon.
Epoxy.com Product #406 Pigmented will yield approximately 3.5 mils dry film thickness when
spread at 300 ft2 per gallon.
COLOR SELECTION
Epoxy.com Product #406 is available in Clear (gloss or satin) and 17 colors. Custom Colors
are available subject to laboratory approval, minimum quantity, lead time for production, and increased cost.
TECHNICAL DATA
| Viscosity @ 75ºF |
125-150 cps, mixed, Clear |
|
Mixing Ratio |
3 Parts A to 1 Part B by Volume |
| Solids Content (by Volume) |
54.26% Clear
66.46% Pigmented |
| Volatile Organic Content (VOC) |
1.56#/gal (187 gm/L) Clear
1.39#/gal (166 gm/L) Pigmented |
| Weight per Gallon |
9.85 pounds per gallon , mixed, clear |
CURE/DRY TIME
| Pot Life |
8 hours @
75ºF |
| Dry to Touch |
10-14 hours @ 75º |
|
Re-Coat |
12-16 hours @ 75º |
| Light Service |
16 hours @ 75º |
| Full Cure & Maximum Resistance |
5-10 days |
AVAILABILITY
Contact Epoxy.com
MAINTENANCE
After completing the application of Epoxy.com Product #406, the installer should provide the owner with maintenance instructions.
Epoxy.com Product #406 is easily cleaned with neutral
soaps or detergents.
TECHNICAL SERVICE
Epoxy.com Technical Support provide services and consultations on material selection, specification,
troubleshooting, and other information on the proper repair and protection of
concrete surfaces.
CHEMICAL RESISTANCE
REAGENT RATING
- Acetic Acid-5% L
- Acetone L
- Betadine R
- Beer R
- Bleach L
- Brake Fluid R
- Citric Acid-30% R
- Citric Acid-40% L
- Crude Oil R
- Diesel Fuel R
- Ethylene Glycol R
- Fatty Acids L
- Gasoline R
- Hydrochloric Acid-15% R
- Iodine R
- Lactic Acid-15% R
- Methyl Ethyl Ketone L
- Nitric Acid-10% R
- Orange Juice R
- Peroxide-35% R
- Phosphoric Acid-85% L
- Skydrol R
- Sodium Hydroxide-50% R
- Sulfuric Acid-20% R
- Toluene R
- Urea R
- Vinegar L
- Xylene R
R-Recommended for continuous service.
L-Limited Recommendation, occasional spills.
*-May cause slight stain or discoloration.
Untitled Page
Proper mixing and installation is critical to the optimal success of all
product. See Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
375 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2007 EPOXY.COM a
division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy
Systems™ Product Company ("ESI") warrants its products (when properly stored)
for the period of time as follows: Epoxies, Product #315, Product #315BC, and
Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2)
months and Polyurethanes Four (4) months; Power Tools and Equipment 90
days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all
other resins (not specifically mentioned above) 30 days; hand tools (non-power
tools) 30 days. ESI warrants that its products will be free of
manufacturing defects and will be in conformity with published specifications
when handled, stored, mixed and applied in accordance with recommendations of
ESI. If any product fails to meet this warranty, the liability of ESI will be
limited to replacement of any non-conforming material if notice of such
non-conformity is given to ESI within the warranty period for the material (as
indicated above), or within 1 year of the delivery of materials (whichever is
sooner). ESI may in its discretion refund the price received by ESI in lieu of
replacing the material. No customer, distributor, or representative of ESI is
authorized to change or modify the published specifications of this warranty in
any way. No one is authorized to make oral warranties on behalf of ESI. In order
to obtain replacement or refund the customer must provide written notice
containing full details of the non-conformity. ESI reserves the right to inspect
the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED
WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY
UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE
PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY,
WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of
our products are made on an individual order basis. Unless
authorized in writing by Epoxy Systems, Inc. in writing before the material is
made, there are no returns on items purchased from us, once the order has been
processed, and the material made. In the event of authorized returns a
restocking charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on non-list
priced items. All Returns are for merchandise (store) credit only, no cash
or credit card credits. In the event of a return, buyer is responsible for
the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
Secure Login