Epoxy.com Product #1 - ESD
Electro Static Dissipative Epoxy Coating
Ultra High Solids Epoxy Coating
Epoxy.com Product #1 - ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring is an ultra high solids bis-A epoxy floor coating designed to provide
electrostatic control properties to various surfaces including concrete or other nonconductive substrates. The use of a conductive primer will transmit conductive readings through
Epoxy.com Product #1 - ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring if applied no thicker than 15 mils.
Epoxy.com Product #1 - ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring provides excellent bond to concrete as well as high impact and wear.
- Easy Application
- Dissipates a 5000 volt Charge to Zero in less than 0.1 Seconds @72°F
- Available in Static Dissipative Range of 1,000,000 to 1,000,000,000 ohms
per EOS/ESD Standards.
- Consistent Electrical Resistance Ratings When Tested at 10-500 Volts.
- High Gloss
- Good Abrasion Resistance.
- Easy to Clean..
Ultra High Solids Bis-A Epoxy Resin and Conductive Fillers.
Epoxy.com Product #1 - ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring is available in Epoxy.com Colors listed to the right. Custom colors available as approved.
Surface preparation is considered to be the most important step of any
resinous flooring application. Improper surface preparation could turn what
seems to be a simple process into a lengthy, difficult repair. See Epoxy.com
Surface Preparation Guide for proper surface preparation
procedures. When in doubt you should always contact Epoxy.com Technical
Support with your questions.
Epoxy.com Product #1 - ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring is normally spread with a
trowel or squeegee and back-rolled with a 3/8” medium nap roller. Care should be taken to minimize the entrapment of air caused by
Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.
Epoxy.com Product #1 - ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring will yield 12-15 mils
when spread at 100-130 sq ft/gal. 15 mils is considered the maximum thickness.
After completing the application of Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat and the topcoats or floor covering system, the installer
should provide the owner with maintenance instructions relevant to the specific topcoats or floor covering. If floors become slippery due to
animal fats, oil, grease, or soap film, clean and rinse thoroughly.
Contact Epoxy.com Customer Service Department.
|Flammability ||ASTM D-635
|Fungus & Bacteria Growth
||Will not support growth of fungus or bacteria
when subjected to mildew
|Hardness ||ASTM D-2240
||70-80 Shore D
|Bond Strength to Concrete
||Greater than 300psi (100% concrete failure)
|Thermal Shock Resistance
||100 in-lbs direct
||35-40 Min. (@73°F)
||14-16 hours (@73°F )
||5 days (@73°F.)
||Less than 50gm/l
|Weight per Gallon
||10.5-11 lbs per gal.
||Greater than 80|
Contact Epoxy.com Technical Support Department
Proper mixing and installation is critical to the optimal success
of all product. See
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
For more information please contact:
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Florida & Vermont
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
352-533-2167 Norm Lambert, President - Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
|| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers.|
Copyright © 1994-2013 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
other wise agreed upon in writing, buyer is responsible for the cost of
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]