|
Epoxy Novolac Mortar and Coating
Highly Chemically Resistant Epoxy Mortar and Chemical Resistant Epoxy Flooring
Epoxy.com Product #630 - 100% Solids Zero (0) VOC - Meets Low VOC Standards
DESCRIPTION
Product #630 Highly Novolac Chemical Resistant Epoxy Mortar and Chemical Resistant Epoxy Flooring is a 100% solids epoxy Novolac ideal for harsh chemical and solvent resistant applications. Product #630 Highly Novolac Chemical Resistant Epoxy Mortar and Chemical Resistant Epoxy Flooring is ideal for use as a troweled mortar, slurry binder, and coating for concrete and steel in extremely corrosive areas where resistance to 98% sulfuric acid or other strong caustics is needed.
Product #630 Highly Novolac Chemical Resistant Epoxy Mortar and Chemical Resistant Epoxy Flooring is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities.
ADVANTAGES
- Exhibits excellent resistance to strong acids, alkalis, and most industrial chemicals and solvents
- Can be applied in cool damp conditions
- Can be re-coated in 7 to 8 hours
- Can be applied in occupied facilities
- Clear formulation is excellent for colored quartz applications.
CONSIDERATIONS
- Concrete substrate must be free of dirt, waxes, curing agents, and other foreign materials.
- Steel surfaces must be free of grease and oils. Abrasive blast.
COMPOSITION
100% solids, modified cycloaliphtic cured epoxy Novolac resin.
APPLICATION
SURFACE PREPARATION
Surface Preparation is the most critical portion to any successful resinous system application. All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation Procedures. The Epoxy.com tech service department is pleased to answer any questions.
INSTALLATION
Will vary with application method.
PHYSICALPROPERTIES |
|
| Color | Clear, & The Colors Listed Below. Custom colors available. |
| Solids Content | 100% |
| Gloss 60° F | 90 |
| Viscosity | Part "A": 4500-6500 cps Part "B": 60-75 cps Mixed: 1000-1500 cps |
| Mix Ratio | 2A to 1B by volume |
| Pot Life | 20 - 25 minutes @ 75°F |
| VOC | 0% |
Click the picture
of color card at the side for a larger version of this picture of the
color chart.
Please note:
The picture to the right is a photographic reproduction
of the color card for this product. The photo reproduction process and
your monitor and/or printer will change these colors. This chart is to
give you an idea of the colors available and not intended for critical
color selections.
DRY TIME | |
| Foot Traffic | 6-7 hours |
| Recoat | 8 - 12 hours |
| Service | 3-5 days |
PERFORMANCE PROPERTIES |
|
| Tensile Strength ASTM-D-638 | 4,000 psi |
| Compressive Strength ASTM-D-695 | 11,000 psi |
| Adhesion to concrete ACI Committee 403 | 300 psi - 100% concrete failure |
| Hardness ASTM-D-2240 | 85 Shore D |
| Abrasion Resistance ASTM-C-501 CS-17 Wheel | 30 mg lost |
| Service Temperature MIL- D-3134F | Up to 180-325 degrees F. Dry Heat |
| Impact Resistance Mil-D-3134F § 4.7.3 | 16 ft. Lbs |
| Indentation MIL-D-3134F §4.7.4 | No Indentation |
| Elevated Temperature Resistance MIL-D-3134F § 4.7.5 | Passed |
| Water Absorption ASTM-D-570 (24. Hr. Immersion) | 0.10% |
CHEMICAL RESISTANCE
R-Recommended for Immersion service (greater then 6 months). S1- Slash & Spill 7 day clean-up. S2 Splash & Spill 24 hour clean-up. S3 Splash & Spill hourly clean-up . ND - Not Determined.
Chemical |
Resistance Rating |
| Acetic Acid 20% | R |
| Acetone | S3 |
| Aluminum Chloride - 30% | R |
| Aluminum Nitrate - 50% | R |
| Aluminum Sulfate - 50% | R |
| Ammonium Hydroxide- 30% | R |
| Ammonium Sulfate - 50% | R |
| Ammonium Sulfide - 50% | R |
| Barium Sulfate | R |
| Barium Sulfide | R |
| Beer | R |
| Benzene | S2 |
| Benzyl Alcohol | R |
| Black Liquor | R |
| Butyl Acetate | R |
| Brake Fluid | R |
| Butanol (Normal) | R |
| Calcium Chloride | R |
| Calcium Hydroxide | R |
| Citric Acid - 40% | S1 |
| Corn Oil | R |
| Crude Oil - Sour | R |
| Crude Oil - Sweet | R |
| Cutting Oil | R |
| Cyclohexeone | S3 |
| Diacetone Alcohol | S2 |
| Diesel Fuel | R |
| Diethylene Glycol | R |
| Distilled Water | R |
| Ethanol | R |
| Eythl Acetate | R |
| Ethyl Alcohol | R |
| Ethylene Dichloride | S1 |
| Ethylene Glycol | R |
| Fatty Acids | R |
| Freon | S1 |
| Fuel Oil | R |
| Gasoline - Unleaded regular | R |
| Gasoline -Unleaded premium | R |
| Glucose | R |
| Glycerin | R |
| Glyoxal - 40% | R |
| Heptane | R |
| Hexane | R |
| Hexylene Glycol | R |
| Hydraulic Fluid | R |
| Hydrochloric Acid -10% | R |
| Hydrochloric Acid-36% | R |
| Hydrogen Peroxide 5% | R |
| Iodine | R |
| Isobutyl Alcohol | R |
| Isopropyl Alcohol | R |
| JP-4 Jet Fuel | R |
| JP-5 Jet Fuel | R |
| Kerosene | R |
| Ketchup | R |
| Lactic Acid | R |
| MAK | ND |
| Methyl Ethyl Ketone | R |
| Methanol | R |
| MIBK | R |
| Mineral Spirits | R |
| MTBK | R |
| Nitric Acid - 10% | R |
| Oxalic Acid | R |
| Peanut Oil | R |
| Perchloroethylene | R |
| Phosphoric Acid 10% | R |
| Phosphoric Acid 75% | R |
| Phosphoric Acid 85% | R |
| Power Steering Fluid | R |
| Skydrol | R |
| Sodium Hydroxide - 50% | R |
| Sodium Hydroxide - 70% | R |
| Sodium Hypochlorite 10% | R |
| Sodium Nitrate - 50% | R |
| Sulfarnic Acid | R |
| Sulfuric Acid 10% | R |
| Sulfuric Acid 50% | R |
| Sulfuric Acid 70% | R |
| Sulfuric Acid-98% | R |
| Toluene | R |
| Tomato Juice | R |
| Transmission Fluid | R |
| Urine | R |
| Vinegar | R |
| Vinyl Tolene | R |
| White Liquor | R |
| Xylene | R |
Other customers who visited this page also visited:
- Product #1 - All Purpose Epoxy Floor Coating
- Product #1W - Wall Grade Version of Product #1 All Purpose Epoxy Floor Coating
- Product #2 - Chemical Resistant Epoxy Floor Coating.
- Product #632 Novolac Epoxy Joint Filler
- Product #633 Novolac Coating
- Epoxy Chip Flooring System
- Epoxy Coatings Page.
For more information please contact:
Epoxy.com
A Division of
Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems
,
Since 1980 - Over 33 years
Florida & Vermont
USA
Customer and Technical Support Hours: 9AM-4PM Eastern Time
(6AM-1PM Pacific Time)
.
Closed 12 Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order
Status
Katey Fontaine, VP - Customer
Service Director
sales@epoxy.com
Technical Support
352-533-2167 Norm Lambert, President - Technical
Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
|
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers. |
Copyright © 1994-2015 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved.