Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Conductive Epoxy Coating NT

Conductive Nano-Tube Filled Epoxy

Product #1 ESD-NT


Product #1 ESD-NT is a 100% solids bis-A epoxy floor coating designed to provide electrostatic control properties to various surfaces including concrete or other non-conductive substrates. Product #1 NT-ESD has good chemical resistance and is ideal for any areas requiring electrostatic dissipative or conductive surfaces, provides excellent bond to concrete as well as impact and wear resistance. Application over a non-conductive primer or basecoat will transmit ESD readings of less than 1,000,000,000 ohms through Product #1 NT-ESD. Application over Product #668 CONDUCTIVE PRIMER will transmit conductive readings of less than 1,000,000 ohms through Product #1 NT-ESD.


  • Carbon nanotube technology: Consistent electrical resistance readings regardless of film thickness
  • ESD/Conductive properties for life of the coating
  • Meets USGBC LEED criteria for low VOC, low odor
  • Gloss finish, easy to clean
  • Good chemical resistance and abrasion resistance
  • May be sealed with Epoxy.com -ESD Urethane for enhanced performance properties
  • Tests less than 1x109 ohms conforming with ANSI/ESD S20.20 standard when applied over non-conductive primer or basecoat
  • Tests less than 1x106 ohms conforming with ANSI/ESD S20.20 standard when applied over Product #668 Condutive Primer
  • Body Voltage Generation (BVG) below 100 volts conforming with ANSI/ESD S20.20 standard
  • Dissipates a 5000 volt charge to zero in less than 0.1 seconds @ 72° and 12% RH

Considerations for Use

  • Substrate temperature must be a minimum of 55-60°F and maximum of 85°F
  • Relative Humidity should be 30-85% and substrate temperature must be 5°F above the measured dew point
  • Refer to Epoxy.com Surface Preparation guide regarding substrate requirements and surface preparation
  • Apply at 20-35 mils, application at <20 mils will create a prominent orange peel finish


100% solids bis-A epoxy resin and fillers.


Product #1 NT-ESD will yield approximately 20-32 mils when spread at 50-80 ft2 per gallon.

Color Selection

Product 1 NT-ESD s available in NT-ESD Standard Colors only, contact Epoxy.com for color selection samples. The colors will vary slightly from Epoxy.com Standard Colors due to the conductive filler content.



Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation Procedures. The Epoxy.com Technical Service Department is available to answer any questions.


Installation of Product #1NT-ESD will vary with application. Typically spread in a single coat at 50-80 ft2 per gallon with a 25-30 mil notched Easy-Squeegee and lightly back-roll with a medium nap roller, immediately with cross rolling using a spiked roller. Optional use of a metal-tined spiked roller will improve leveling of the coating.

IMPORTANT: 20 mils is considered the minimum thickness to avoid a prominent orange peel texture, depending to some extent on using a spiked roller. Optional: Add 10% MEK or Anhydrous Isopropyl Alcohol (99%) as thinner to reduce orange peel use ONLY these specific thinners. Care should be taken to minimize the entrapment of air caused by over rolling. For complete instructions, consult Epoxy.com Technical Service.


Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner. Consult Safety Data Sheet (SDS) for safety and health precautions.

Cure and Drying time

Working Life 20-35 min @75°F
Minimum Recoat Time 12-14 hours @75°F.
Light Foot Traffic 24-30 hours @75°F
Wheeled Traffic 36-48 hours @75°F
Full Chemical and Max Resistance  7 Days 7@5°F

Technical Data

Mix Ratio  2 Part A to 1 Part B by Volume
Solids Content  99% Solids by Volume 
Volatile Organic Content (VOC)  <50 g/L, Compliant to low VOC
(EPA method 24)   Rule 1113 in all 50 states  
Gloss (60°)  80-90 
Unit Sizes Available  3 gallons, 15 gallons  
Shelf Live   12 months  

Physical Properties

Abrasion Resistance  ASTM D4050
CS-17 Wheel, 1000 Cycles 
70-100 mgs 
Adhesion to Concrete ASTM D7294 300-400 PSI
Concrete Failure
varies by concrete strength
Flammability  ASTM D635  Self Extinguishing 
Hardness Shore D  ASTM D2240  75-80 
Chemical Resistance    Contact Epoxy.com Tech Support 
Conductivity Resistance  ANSI/ESD-S7.1  Conductive Range: Less than 1,000,000 ohms 
ESD Range: Less than 1,000,000,000 ohms
Static Charge Decay Mil-B-817058 Dissipates a 5,000 volt charge to zero in < 0.1  Seconds


Contact Epoxy.com Customer Support Department

Technical Support

Contact Epoxy.com Technical Support Department


After completing the application of Product #1NT-ESD, the installer should provide the owner with the maintenance instructions. Product #1NT-ESD is easily cleaned with neutral soaps or detergents. Contact Epoxy.com Technical Support with your additional questions.

Proper mixing and installation is critical to the optimal success of all products.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

A Division of Epoxy Systems, Inc
A Vermont Corporation

We have products that have passed the test of time as well as the best new Systems available today.

Since 1980 - 40 years of the highest quality products

Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)

Closed for lunch from 12Noon to 1PM

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Lambert-Fontaine, VP - Chief Operations Officer

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

Copyright © 1994-2023 (providing online information about the right product for the right job for nearly 30 years)  EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.