Epoxy Rebar Touch Up Coating

DESCRIPTION

Product #OSVX470 Epoxy Rebar Touch Up Coating, is a two component, 70% solids epoxy coating specially manufactured to touch up damage epoxy coated rebar or to coat rebars not previously protected against corrosion.

ADVANTAGES

#OSVX470 Epoxy Rebar Touch Up Coating can be field applied. For best results apply at temperatures of 50°F and rising.

PHYSICAL PROPERTIES

Color	Green (other colors available upon request)
Weight per gallon	10 lbs.
Viscosity	3000 cps
Solids	70% by weight
Shelf Life closed container	12 months
Pot Life	8 hours
Drying time at 70°F	Overnight
Closed cup flash point Part A Part B	76°F (24°C) 88°F (31°C)

SURFACE PREPARATION

Surfaces to receive Product #OSVX470 Epoxy Rebar Touch Up Coating should be dry and free of oil, grease, dust, scale, rust and damaged coating.

Mixing

Stir Components "A" and "B" thoroughly before mixing. Combine one part by volume of "A" with one part by volume of "B" (mixing ratio 1:1). Mix for not less than three minutes, using a slow speed drill, (300 to 600 rpm) and an Epoxy.com Mixing Paddle. When mixing has been completed, cover mixed material and allow an induction time of not less than 45 minutes before application.

APPLICATION

#OSVX470 Epoxy Rebar Touch Up Coating can be applied by brush or roller.

COVERAGE

Product #OSVX470 Epoxy Rebar Touch Up Coating when applied at an approximate rate of 300 square feet per gallon will provide a film thickness of 5.25 mils wet and 3.75 mils dry. Two (2) coats are recommended

PACKAGING

Product #OSVX470 Epoxy Rebar Touch Up Coating is packaged in two (2) gallon and ten (10) gallon units.

CAUTION

"A" Component: May cause skin sensitization or other allergic responses. Avoid inhalation of vapor. Use good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier cream. If contact with skin occurs, wash immediately with soap and water. In case of contact with eyes, flush immediately with water and contact a physician.

CAUTION! DANGER! Contains alkaline amines; strong sensitizer. Do not get into eyes, on skin or clothing. Avoid breathing vapor. Keep container closed. Use with adequate ventilation. Wash thoroughly after handling.

FIRST AID

In case of contact, immediately flush eyes or skin with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Call a physician. Wash clothing before reuse. Discard contaminated shoes. Wear protective clothing, goggles, gloves and/or barrier creams.

FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.

Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com

352-533-2167 Technical Support
Norm Lambert, President - Technical Support Director
info@epoxy.com

352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com

352-489-1625 Fax line to all Departments

Website: www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc. (hereinafter known as "Supplier" warrants its products (when properly stored) for the period of time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylate and Polyurethanes Six (6) months. Supplier warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Supplier. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Supplier within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material. No customer, distributor, or representative of Supplier is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Supplier. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Supplier reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis. Unless authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

[Home] [Catalog of Products] [MSDS in Acrobat Format] [Online Ordering Authorization Form] [Add Epoxy.com to Favorites]