[Epoxy Home] [Catalog of Products] [Where to Start] [Guide Specs] [Epoxy Installation Guides] [Blog Posts] [Epoxy Bonding Systems] [Chip Floors] [Chemical Resistant Epoxy] [Seamless Coatings] [Conductive Epoxy Flooring] [Crack Injection of Concrete & Wood] [Applications] [Elastomeric Polyurethane Systems]  [Seamless Garage Flooring Resins] [High Temperature Epoxy Resins] [Seamless Industrial Floors] [Joint Systems & Sealants] [Methyl Methacrylate MMA ] [Novolac Epoxy Resins] [Epoxy Mortars & Grouts] [Epoxy Novolac] [Primers Sealers] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Epoxy Installation Tips] [Who We Are]  [Epoxy Tech Data Sheets in Acrobat] [Product MSDS Sheets] [Online Order Authorization Form][Contact UsPhone 352.489.1666

  Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980Contact Us  





SCOPE: The work covered by this division of the specifications consists of furnishing all labor, materials and equipment to perform all operations in connection with the complete installation of the pressure injected epoxy as shown on the Drawings and/or as specified herein.

MATERIALS: All material shall be new, of first grade quality.

A. Epoxy injection resin (for wet or dry application) shall be Epoxy.com  Injection Binder Product #301 as supplied by Epoxy.com a divison of Epoxy Systems, Inc.,
a Vermont Corporation with Principal offices at:
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
352-489-1666 (voice)
352-489-1625 (fax)

1. General Requirements

a. Capable of penetration and performance in concrete separation 15 mils and greater in width.

b. Chemical resistant

c. Abrasive resistant

2. Special requirements

Mix Ratio 2:1 by Volume
Gel Time 10.8 minutes
Color Light Amber
Viscosity Mixed - ASTM D-2393 400-450 cps
Initial Cure 24 hours
Final Cure 7 days
Packaging gallons, pails, drums


Concrete Bond Strength (ASTM C-882) 2,280 p.s.i
Compressive Strength (ASTM D-695) 10,000 p.s.i
Tensile Strength (ASTM D-790) 3,500 p.s.i
Elongation (ASTM D-638) >10%
Adhesion to Concrete (ACI Committee 403) 250 p.s.i (Concrete Fails)

B. Epoxy Paste Surface Seal shall be Epoxy.com Epoxy Bonding Paste Product #5 (fast setting), or Product #6 (slow setting), as supplied by Epoxy.com a division of Epoxy Systems, Inc. of Dunnellon, Florida, and Vermont

1. General Requirements

a. Two component epoxy resin which meets or exceeds requirements of epoxy resin Type I, Grade 1, class A per ASTM C881-78.

b.     100% solid by weight

c.     Viscosity of paste.

d.     Capable of application, adhesion, and curing when applied on frost-free and dry surfaces at temperatures down to zero degrees F., and when applied on moist surfaces at temperatures above 32 degrees F.

e. 7 day Compressive Strength not less than 10,900 p.s.i (ASTM D-695).

f.     Tensile Strength (ASTM D-638) 5,300 p.s.i

g.     Tensile Elongation (ASTM D-638) 4% - 9%

h.     Pot Life (200 gr.) 9 minutes (minimum) 63 (maximum)

i.     Shore D Hardness (ASTM D-2240) 83

C. Polyester Surface Seal Shall be Epoxy.com Product #48–Filler 7 as supplied by Epoxy.com a division of Epoxy Systems, Inc. of Dunnellon Florida and  Vermont.

1. General Requirements

a.  Mix ratio 100 R to 2 H.

b. 100% solid by weight.

c. Viscosity of paste.

d. Capable of application on dry surface down to 0°F.

e. Density (lbs./gal) 14.13 (ASTM D-1475)

f. Specific Gravity (g/cm3) 1.70 (ASTM D-792)

g. Peak Service Temperature 400°F.

h. Pot Life (100 grams @ 77°F) 4-7 min.

i. Shore D Hardness 88-90 (ASTM D-2240)



A. Vacuum chuck and hollow drill bits.

B.     The equipment used to inject the epoxy shall be acceptable to the epoxy manufacturer and shall conform to all of the following:

1. Capacity to automatically proportion the epoxy material by was of positive displacement type pumps for each components. These pumps shall have the capacity of proportioning components within the tolerances set by the epoxy manufacturer.

2. Capacity to automatically mix the epoxy materials completely in line. Batch mixing will not be permitted.

3. Capacity to inject the epoxy resin under controlled, variable pressures.

4. Capacity to heat each component's reservoir container, and injection hose, so as to enable the heating of the resins to optimal injection temperature.



A. The top surface of the cracks designated for injection shall be cleaned free of dust, silt, laitance, oil and grease, or any other material that would interfere with the bond of the surface sealer.

B. Entry ports for epoxy shall be provided, spaced far enough apart to assure that when the adhesive material shows at the adjacent port, it has completely filled the crack to it's full depth. Entry ports shall be spaced along cracks and spacing usually determined by the tightness of the crack and the depth of the concrete substrate. Spacing is generally between 6 and 14 inches. A small reservoir shall be provided below the bottom of the port to aid in resin flow.

C. Injection ports shall be inserted into the drilled holes to about 1/2 inch allowing for the small reservoir below the port. The ports are then bordered into position with Epoxy Bonding Paste Product #5or #6, for wet or dry applications, or Epoxy.com Product #48 (Filler 7), for dry applications. Care will be taken not to seal the ports from resin flow. If surface port system is used, care will be taken to insure that the crack is open at the point below the port, and that there is a proper reservoir beneath the port.

D. A surface seal or epoxy patch meeting the requirements of this specification shall first be applied to the exterior crack to prevent the escape of the injection resin. The cracks shall be covered with a bead of Epoxy Bonding Paste Product #5, #6 or #48 and smoothed with a putty knife to insure sealing.

E. Injection of the epoxy resin into a crack shall, unless permitted by the Engineer, begin first at the entry port of lowest elevation and continue until uncontaminated epoxy flows out of the adjacent port. Injection pressure shall be kept as low as practical and shall generally be between 20 p.s.i and 30 p.s.i plus any hydrostatic head. The connection between the entry port and the mix head of the injection nozzle must be sufficiently tight to prevent epoxy from running out on the concrete surfaces.

F. After injection at a given port is complete, this port shall be plugged and injection started at the next adjacent port. This procedure shall be repeated until the crack is completely filled. Upon completion surface to be left as noted on the Drawings.



A. The overall quality of the work shall be judged by the Contractors ability to achieve 90% penetration of the cracks. In case of a question as to quality of work, the Engineer will have core samples taken from the completed work and assess the completeness of crack penetration.

B. The cores will be taken at location(s) determined by the Engineer and paid for by the OWNER. The contractor will not be responsible for the presence of inclusions of foreign matter in the cracks and susceptibility of such foreign matter to be removed by the recommended cleaning practices.


It is expected that the contractor will furnish adequate labor, material and equipment such that the work will progress with out any undue and unnecessary interruption.

Hit Counter



Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director

 352-533-2167  Technical Support
                         Norm Lambert, President - Technical Support Director 
352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

352-489-1625   Fax line to all Departments

Website:  www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright 1994-2014 (providing online information about the right product for the right job for 20 years) EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  (hereinafter known as "Supplier" warrants its products (when properly stored) for the period of time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylate  and Polyurethanes Six (6) months.  Supplier warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Supplier. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Supplier within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material. No customer, distributor, or representative of Supplier is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Supplier. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Supplier reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.


[Home] [Catalog of Products [MSDS in Acrobat Format]  [Online Ordering Authorization Form] [Add Epoxy.com to Favorites]

Hit Counter