|
|
|
EpoxySystems'™ Product #415 Changed to Product 452 Elastomeric Polyurethane Coating
EPOXYSYSTEMS’ PRODUCT #415 is a liquid applied, single component, moisture-cured polyurethane. It is the major component of all EPOXYSYSTEMS’ deck coating systems. Composition: Liquid-applied, single-component, moisture-cured, polyurethane elastomer. All materials shall be delivered to the jobsite in unopened containers clearly marked and labeled.
BASIC USES: EPOXYSYSTEMS’ PRODUCT #415 is used to waterproof concrete and plywood decks which are subsequently covered with outdoor carpeting, tile, or wood decking. The product is recommended for all applications which require the waterproof surface to be painted, where a bitumen-extended polyurethane would not be suitable. EPOXYSYSTEMS’ PRODUCT #415 is designed as a high performance elastomeric covering over spray applied, polyurethane foam roofs. EPOXYSYSTEMS’ PRODUCT #415 is available in a special thixotropic consistency for use over irregular surfaces such as foam roofs. PRODUCT #415 must be coated with EPOXYSYSTEMS’ PRODUCT #416 if it is used over foam insulated roofs.
SURFACE PREPARATION: All surfaces which are to be coated with EPOXYSYSTEMS’ PRODUCT #415 must be free of contamination such as curing compounds, concrete hardeners, bond breakers, paint, etc. All surfaces must be dry, having a maximum water content of 20%. We recommend water-curing concrete instead of using concrete curing compounds. Only exterior grade plywood should be used. Concrete should be cleaned by sandblasting, or other abrasive method. Allow a minimum drying time of 72 hours. Except for non-moving shrinkage cracks, all other cracks and joints must be sealed with EPOXYSYSTEMS’ PRODUCT #905. All surfaces, where necessary, must be primed with EPOXYSYSTEMS’ #890 PRIMER prior to application of the coating system at a rate of 350 square feet per gallon (8.6 m2/gallon), except for plywood in good condition. All seams between plywood sheets and those between metal flashing and the plywood deck must be reinforced by imbedding a 2 inch (5 cm) wide strip of glass cloth tape in wet EPOXYSYSTEMS’ PRODUCT #415, which is brushed evenly over the seam in a width of about 3 inches (7.6 cm) and a thickness of about 20 mils (0.5 mm) wet. The application of EPOXYSYSTEMS’ PRODUCT #415 can subsequently be made immediately over the entire area, including the taped areas. Cracks in concrete must be treated in the same way. Where EPOXYSYSTEMS’ PRODUCT #415 is used as a protective coating on polyurethane foam roofs, it must be applied within 8 hours from the time the foam is installed.
EPOXYSYSTEMS’ PRODUCT #415 shall be applied at a rate of 60 square feet per gallon (1.5 m2/Liter) per coat resulting in a 25 dry mil (0.6 mm) thickness. Most applications require two coats at this coverage, allowing a 24 hour cure time between coats. EPOXYSYSTEMS’ # 415 can be applied by airless spray equipment, rollers, or squeegees. Airless spray equipment must have a minimum of 30 to 1 ratio. Permit a 48 hour cure time after the final coat is applied before continuing with tile setting, carpet laying, back filling, or any other operations.Shelf Life: 6 months at 77°F (25°C), unopened. Color: Concrete Grey, Tan Sizes: Available in 1 gallon cans, 5-gallon pails and 55-gallon drums. Weighs 9.8 lbs. per gallon (4.45 kg/gallon). PHYSICAL PROPERTIES:
PRODUCT WARRANTY: All products proven to be defective in manufacture will be replaced at no charge. Since the use of these products is beyond our control we cannot accept damage in excess of the purchase price of these products. MAINTENANCE: If EPOXYSYSTEMS’ PRODUCT #415 is damaged, it can be repaired by cleaning
the surface with M.E.K. and recoating it with EPOXYSYSTEMS’ PRODUCT #415. FOR INDUSTRIAL USE ONLY / KEEP AWAY FROM CHILDREN
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
