Fast Set Flooring

[Home] [Catalog of Products] [Where to Start with Epoxy] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Coatings] [Conductive]  [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy] [Polymer Systems] [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Wood Filler] [Who is Epoxy.com] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [MSDS in Acrobat Format] [Online Ordering Authorization Form]
  Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980  

 Epoxy.com Product #316

Ultra Fast Setting Epoxy Flooring/ Mortar Resin

DESCRIPTION

Epoxy.com PRODUCT #316 is a 100 % solids fast setting two-component epoxy resin system. Epoxy.com PRODUCT #316 is made to set fast even in temperatures below freezing. It is recommended for flooring, injection or anchor-bolt grouting in the neat state or as a mortar when mixed with up to 3 parts of Epoxy.com PRODUCT #75 Filler (by volume). Epoxy.com PRODUCT #316 exceeds most requirements of ASTM C-881-99, Types I and IV , Grade 1, Class A.

ADVANTAGES

Usable to 10oF on concrete

Will cure at low temperatures.

Does not shrink in curing.

Abrasion and chemical resistant.

Will produce structural properties within 24 hours.

WHERE TO USE

FLOORING - REPAIR AND COATING
PRESSURE GROUTING DAMP OR DRY CRACKS
ANCHOR BOLT GROUT
CONCRETE SEALER
MORTAR FOR GROUTING BASE PLATES

PHYSICAL PROPERTIES

Color

Mixed Epoxy – Straw

Mixing Ratio

2A to 1B by volume

Viscosity

4000 cps @ 40oF 1000 cps @ 70oF

Pot Life

20 min. @ 40oF 5 min. @ 70oF

Gel Time

25 min. @ 40oF 10 min. @ 70oF

Shore D, Hardness

80

Compressive Strength ASTM C 109 Modified

40oF (4oC)              70oF (21oC)

Neat Epoxy:

1 day 12,500 psi       13,500 psi
7 days 13,000 psi     13,500 psi
14 days 14,000 psi   14,000 psi

Filled: (3 1/4 parts filler)

1 day 5,000 psi         9,500 psi
7 days 6,500 psi       9,500 psi

Tensile Strength ASTM D-638

1 day                        8,000 psi

SURFACE PREPARATION

All surfaces to receive Product #316 must be free of dirt, grease, curing compound, liquid contaminants, heavy laitance and soft or deteriorated concrete. It's recommended that abrasive blasting, water blasting or acid etching with a 10% solution of commercial muriatic acid be utilized for surface preparation. Vacuum all areas prior to application to remove fine particles of cement or sand. Surface must be sound.

MIXING

Combine two parts by volume of "A" Component with one part by volume of "B" Component (mixing ratio is 2:1). For best results, mix entire unit. The blend should be thoroughly mixed for at least two minutes with a low speed 1/2" electric drill and Epoxy.com-Mixing Paddle. If used as a mortar, introduce the Epoxy.com PRODUCT #75 Filler slowly while mixing to assure proper aggregate saturation.

APPLICATION

Keep Epoxy.com Product #316 warm where possible. This will facilitate mixing and application. No ice should be present when applying. Apply immediately after mixing. Fast setting be prepared to place. Do not waste time.

YIELD

One (1) gallon (3.8 L) of Product #316, with 3 parts of Epoxy.com PRODUCT #75 Filler, provides approximately 645 cu. in. (1 x 10 cm ) of mortar.

LIMITATIONS

Do not thin; solvents will prevent proper cure. Use only oven-dry aggregate to avoid encapsulation of moisture.

CAUTION

"A" Component contains epoxy resin. DANGER! "B" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.

FIRST AID

In case of skin contact, immediately wash with soap and water. in case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing shoes. If irritation persists, seek medical attention. Wash clothing before reuse.

 

FOR INDUSTRIAL USE ONLY

KEEP AWAY FROM CHILDREN

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

 352-533-2167  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Website:  www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright © 1994-2013 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com  within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com  SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products]  [Tech Data Sheets in Acrobat Format] [Epoxy.com MSDS in Acrobat Format]  [Epoxy.com Online Ordering Authorization Form] [Add Epoxy.com to Favorites]

Hit Counter

 

Epoxy.com Secure Login