Epoxy.com Product #27
Slow Setting Mortar Pack
DESCRIPTION
Epoxy.com Product #27 Grout/Mortar Pack is a
preproportioned 100% solids epoxy resin pack and a blend of
special aggregate. The pot life of Product #27 is 3 times
longer than ordinary epoxy packs; while curing the entire pack,
a low exotherm is produced.
ADVANTAGES
- Premeasured to avoid waste while mixing and placing.
- Moisture insensitive before and after cure.
- Pourable viscosity - flows easily, self levels in forms.
- Low heat build-up - low exothermic heat development permits
placement up to 10 inches thick.
- High ultimate compressive strength
- High ultimate Modulus of Elasticity - 2.7 X 106
psi
- No curling or shearing away from substrate (concrete, steel
or wood).
WHERE TO USE
Use in areas where long pot life and extended working time are
required due to higher than normal temperatures or when
placement of an epoxy grout is slow.
PHYSICAL PROPERTIES
|
Viscosity after mixing:
|
Pourable
|
|
Pot Life: 70�F (21�C)
|
1 hr. 45 min.
|
|
Pot Life: 102�F (39�C)
|
1 hr. 15 min.
|
|
Compressive Strength
ASTM C-109 M 28 days
|
9,500
|
|
Modulus of Elasticity
|
2,700,000 psi
|
|
Electrical Properties
Volume Resistivity
ASTM D-257
|
3.03 X 1012 ohm-cm
|
MIXING
Pour Component 'A' into Component 'B'. Mix 2 to 3 minutes. Pour
mixed material into container large enough to accommodate 77
lbs. of filler and resin. Mix slowly for 3 to 5 minutes until
homogeneous mix, gray in color, is achieved.
Note: Do not thin. Solvents will prevent proper
cure.
SURFACE PREPARATION
Substrate must be clean and sound. Remove all laitance, oil, and
grease by sandblasting, wire brushing, or bush hammering. When
used on steel, remove mill scale, rust or any other contaminants
and wipe surface clean with approved metal cleaning solvent.
Patching: Clean out defective area and patch
with Epoxy.com Product #27 and allow to cure
before put into use.
Forming: Epoxy.com Product #27 is a
self-leveling material. Seal forms to prevent seepage. Wax
inside of forms or use bond-breaking liner to prevent adhesion
of grout to form.
APPLICATION
Epoxy.com Product #27 may be placed in single or multiple
lifts up to 10 inches thick. Apply at ambient temperatures as
low as 50�F. Exposure to elevated temperatures for prolonged
periods is not recommended. (Use
Epoxy.com Product #641LV Heat Resistant
Grout up to 400�F).
PACKAGING
- Component "A" is packaged in a 1-gallon can (92.7 fluid oz.)
- Component "B" is packaged in a 1/2-gallon can (64 fluid oz.
- Component "C" Aggregate is in an 77 lb. bag
- Actual yield: .635 cubic feet of grout.
SHELF LIFE
Two (2) years in closed container
CAUTION:
WARNING! A Component contains epoxy resin. May cause skin
sensitization or other allergic responses. Avoid inhalation of
vapor. Use good ventilation, particularly if material is heated
or sprayed. Prevent all contact with skin or eyes. Wear
protective clothing, goggles, gloves, and/or barrier creams. If
contact with skin occurs, wash immediately with soap and water.
In case of contact with eyes, flush immediately with water and
contact a physician.
CAUTION! DANGER "B" component Contains Alkaline Amines. May
cause severe burns, strong sensitizer. Do not get into eyes, on
skin, or clothing. Avoid breathing vapor. Keep container closed.
Use with adequate ventilation. Wash thoroughly after handling.
FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.
